* replaced "dble" intrinsic function by "real" with pReal kind in constitutive_nonlocal.f90
* removed useless line breaks in output of state in CPFEM.f90
* Also added some more openmp directives to increase percentage of parallelized code.
* "implicit none" was missing in two subroutines of homogenization and constitutive.
0 : only version infos and all from "hypela2"/"umat"
1 : basic outputs from "CPFEM.f90", basic output from initialization routines, debug_info
2 : extensive outputs from "CPFEM.f90", extensive output from initialization routines
3 : basic outputs from "homogenization.f90"
4 : extensive outputs from "homogenization.f90"
5 : basic outputs from "crystallite.f90"
6 : extensive outputs from "crystallite.f90"
7 : basic outputs from the constitutive files
8 : extensive outputs from the constitutive files
If verbosity is equal to zero, all counters in debug are not set during calculation (e.g. debug_StressLoopDistribution or debug_cumDotStateTicks). This might speed up parallel calculation, because all these need critical statements which extremely slow down parallel computation.
In order to keep it like that, please follow these simple rules:
DON'T use implicit array subscripts:
example: real, dimension(3,3) :: A,B
A(:,2) = B(:,1) <--- DON'T USE
A(1:3,2) = B(1:3,1) <--- BETTER USE
In many cases the use of explicit array subscripts is inevitable for parallelization. Additionally, it is an easy means to prevent memory leaks.
Enclose all write statements with the following:
!$OMP CRITICAL (write2out)
<your write statement>
!$OMP END CRITICAL (write2out)
Whenever you change something in the code and are not sure if it affects parallelization and leads to nonconforming behavior, please ask me and/or Franz to check this.
* removed input variables in constitutive_collectDotState and constitutive_postResults that are not needed anymore (because of recent changes in constitutive_nonlocal)
Now it is possible to compile a single precision spectral solver/crystal plasticity by replacing mesh.f90 and prec.f90 with mesh_single.f90 and prec_single.f90.
For the spectral method, just call "make precision=single" instead of "make". Use "make clean" evertime you switch precision
* dislocation flux and internal stress calculation now consistent with new definition of slip system lattice according to paper (polarity of screws inverted)
* now complaining when encountering an unknown nonlocal parameter in material.config
* use same error ID for all material parameters out of bounds
* symmetric flux calculation in side dotState can now be omitted (because of new treatment of periodicity)
* switching back to "local flux balance" (add leaving and entering fluxes at central MP, don't touch neighbor) instead of "flux distribution" (subtract leaving fluxes from central MP and add them at neighboring MP). This has the advantage that there is almost no need for CRITICAL statements in parallelization, so hopefully this results in some speed up.
* need to recalculate dislocation velocity in postResults, otherwise we take values of last perturbed state! So the following outputs were up to now showing the perturbed state: shearrate, dislocation velocity, all density rates!
* also put a call to constitutive_microstructure at the start of each crystallite_integration subroutine like it was before. need that for nonlocal model in case of crystallite cutback
* fluxes are now again calculated and distributed only! by the originating material point. this means that the central MP might change the dotState of its neighbor. have to see whether locks slow down parallel computation
* detection of grain boundary in constitutive_nonlocal_microstructure with the help of transmissivity
* enforce positive densities in constitutive_nonlocal_microstructure (needed because dotState does not create cutbacks for negative densities anymore)
* reset single mobile densities below certain threshold to zero (also done in constitutive_nonlocal_microstructure)
* constitutive_nonlocal_kinetics only gets local state variable as input, no need for the entire array here
* dv_dtau is always positive
* multiplication is only active when there is already some initial density of the respective type
* now remembering stiffness similar to how we do it for Lp etc.; avoids undefined stiffness values for nonconverged stiffness calculation
* non-local stuff:
* changed non-local kinetics (Gilman2002)
* enforce zero shearrate for overall carrrier density below relevant density
* enforce zero density for those states that become negative and were below relevant density before
* dislocation velocity is not limited by V^(1/3) / dt anymore
Philip Eisenlohr