- remobilization of immobile singles immediately increases the mobile single dislocation density and therefore directly affects all other mechanisms in dotState
- changed nomenclature (rho -> rhoSgl) to distinguish precisely between single dislocation density and total dislocation density
- changed material.config accordingly
The calculation of the misorientation is now done once in crystallite init and at the end of every FE increment. This saves a lot of time compared to doing it in dotState for every crystallite subinc.
- corrected flux term
- multiplication is now aware of dislocation type
- corrected change rate for "dipole size" dupper
- corrected term for dipole dissociation by stress change
- added transmissivity term in fluxes which accounts for misorientation between two neighboring grains (yet hardcoded transmissivity according to misorientation angle)
- added more output variables
constitutive:
- 2 additional variables "previousDotState" and "previousDotState2", which are used to store the previous and second previous dotState (used in crystallite for acceleration/stabilization of state integration)
- timer for dotState now measures the time for calls to constitutive_ collectState (used to reside in crystallite_updateState, which is not critical in terms of calculation time anymore)
crystallite:
- convergence check for nonlocal elments is now done at end of crystallite loop, not at the beginning; we simple set all elements to not converged if there is at least one nonlocal element that did not converge
- need call to microstructure before first call to collect dotState for dependent states
- stiffness calculation (jacobian): if there are nonlocal elements, we also have to consider changes in our neighborhood's states; so for every perturbed component in a single ip, we have to loop over all elements; since this is extremely time-consuming, we just perturb one component per cycle, starting with the one that changes the most during regular time step.
- updateState gets a damping prefactor for our dotState that helps to improve convergence; prefactor is calculated according to change of dotState
IO:
- additional warning message for unknown crystal symmetry
in constitutive_nonlocal.f90:
Derivatives of shear rates w.r.t. resolved shear stress HAVE to be positive.
Computation of dgdot_dtauslip is now correct.
- read in activation energy for dislocation glide from material.config
- changed naming of dDipMin/Max to dLower/dUpper
- added new outputs: rho_dot, rho_dot_dip, rho_dot_gen, rho_dot_sgl2dip, rho_dot_dip2sgl, rho_dot_ann_ath, rho_dot_ann_the, rho_dot_flux, d_upper_edge, d_upper_screw, d_upper_dot_edge, d_upper_dot_screw
- poisson's ratio is now calculated from elastic constants
- microstrucutre has state as first argument, since this is our output variable
- periodic boundary conditions are taken into account for fluxes and internal stresses. for the moment, flag has to be set in constitutive_nonlocal.
- corrected calculation for dipole formation by glide
- added terms for dipole formation/annihilation by stress decrease/increase
constitutive:
- passing of arguments is adapted for constitutive_nonlocal model
crystallite:
- in stiffness calculation: call to collect_dotState used wrong arguments
- crystallite_postResults uses own Tstar_v and temperature, no need for passing them from materialpoint_postResults
homogenization:
- crystallite_postResults uses own Tstar_v and temperature, no need for passing them from materialpoint_postResults
IO:
- changed error message 229
material.config:
- changed example for nonlocal constitution according to constitutive_nonlocal
all:
- added some flush statements
- take orientation gradients into account when calculating dislocation stress and dislocation fluxes
- hard coded value for nu
- changed kinetics (parameter G0 is currently defined as a parameter, needs to be read from material.config)
- added some output statements
constitutive:
- some functions and subroutines needed additional input variables for passing to constitutive_nonlocal
crystallite:
- some functions and subroutines needed additional input variables for passing to constitutive
- call microstructure with current temperature, Fp, Fe, not "sub0" values
- show number of IPs, that are "onTrack" instead of those not "onTrack"
- calculate Fe at beginning of substep, since we need it for state preguess
(state < relevant state) or (residuum < relative tolerance * state)
since the relevant value for the state variables depend on their nature and can vary by large scales (e.g. volume fraction: 1e-10, dislocation density: 1e5) it is not possible to set a unique value. instead the constitutive law has to decide what is relevant. therefore, all constitutive laws now read in parameters from the material.config that determine the values for relevantState [@luc: in dislobased law relevant State is for the moment generally set to 1e-200, so no additional parameters necessary in material.config. if you also want this feature, we can still implement it, no big deal]
- added sanity checks in constitutive_nonlocal.f90
- corrected coordinate transformation for backstress calculation in constitutive_nonlocal.f90
- corrected equations for evolution of dipole dislocation densities (athermal annihilation and formation by glide)
- dipole dislocations with evolution
crystallite.f90:
- collect state uses subdt and subTstar0_v
- in nonlocal modus: set all crystallites to broken if one is not on track anymore after either stress integration or state update
- constitutive_microstructure is now called inside state update and not in integrate_stress anymore
material.config:
- new parameter for nonlocal constitution
CPFEM.f90:
- age Tstar after increment was finished
- completed postResults output function
- connecting vector of neighboring material points is mapped to intermediate configuration of my neighbor
crystallite.f90
- zero out dotState only when crystallite is non-finished
- set nonfinished flag to false if crystallite is not on Track after state update
- in updateState: set onTrack flag to false if encounter NaN
- removed some old debugging outputs and added others
homogenization.f90
- in debugging mode now telling when a cutback happens
debugging memory leak closed
debugging counters corrected
center of gravity stored in mesh
state updated is now split into a collecting loop and an execution
updateState and updateTemperature fill sequentially separate logicals and evaluate afterwards to converged
added 3x3 transposition function, norm for 3x1 matrix and 33x3 matrix multiplication in math
non-converged crystallite triggers materialpoint cutback (used to respond elastically)
non-converged materialpoint raises terminal illness which in turn renders whole FE increment useless by means of odd stress/stiffness and thus waits for FE cutback
Christoph Kords