minix3/drivers/net/dpeth/3c503.h

71 lines
2.7 KiB
C

/*
** File: 3c503.h Dec. 20, 1996
**
** Author: Giovanni Falzoni <gfalzoni@inwind.it>
**
** Interface description for 3Com Etherlink II boards
**
** $Log$
** Revision 1.1 2005/06/29 10:16:46 beng
** Import of dpeth 3c501/3c509b/.. ethernet driver by
** Giovanni Falzoni <fgalzoni@inwind.it>.
**
** Revision 2.0 2005/06/26 16:16:46 lsodgf0
** Initial revision for Minix 3.0.6
*/
#define EL2_MEMTEST 0 /* Set to 1 for on board memory test */
#define EL2_GA 0x0400 /* Offset of registers in Gate Array */
/* EtherLink II card */
#define EL2_STARTPG (EL2_GA+0x00) /* Start page matching DP_PSTARTPG */
#define EL2_STOPPG (EL2_GA+0x01) /* Stop page matching DP_PSTOPPG */
#define EL2_DRQCNT (EL2_GA+0x02) /* DMA burst count */
#define EL2_IOBASE (EL2_GA+0x03) /* I/O base jumpers (bit coded) */
#define EL2_MEMBASE (EL2_GA+0x04) /* Memory base jumpers (bit coded) */
#define EL2_CFGR (EL2_GA+0x05) /* Configuration Register for GA */
#define EL2_CNTR (EL2_GA+0x06) /* Control(write) and status(read) */
#define EL2_STATUS (EL2_GA+0x07)
#define EL2_IDCFG (EL2_GA+0x08) /* Interrupt/DMA configuration reg */
#define EL2_DMAAH (EL2_GA+0x09) /* DMA address register (High byte) */
#define EL2_DMAAL (EL2_GA+0x0A) /* DMA address register (Low byte) */
#define EL2_VP2 (EL2_GA+0x0B) /* Vector pointer - set to */
#define EL2_VP1 (EL2_GA+0x0C) /* reset address (0xFFFF:0) */
#define EL2_VP0 (EL2_GA+0x0D) /* */
#define EL2_FIFOH (EL2_GA+0x0E) /* FIFO for progr. I/O (High byte) */
#define EL2_FIFOL (EL2_GA+0x0F) /* FIFO for progr. I/O (Low byte) */
#define EL2_EA0 0x00 /* Most significant byte of ethernet address */
#define EL2_EA1 0x01
#define EL2_EA2 0x02
#define EL2_EA3 0x03
#define EL2_EA4 0x04
#define EL2_EA5 0x05 /* Least significant byte of ethernet address */
/* Bits in EL2_CNTR register */
#define ECNTR_RESET 0x01 /* Software Reset */
#define ECNTR_THIN 0x02 /* Onboard transceiver enable */
#define ECNTR_AUI 0x00 /* Onboard transceiver disable */
#define ECNTR_SAPROM 0x04 /* Map the station address prom */
/* Bits in EL2_CFGR register */
#define ECFGR_NORM 0x49 /* Enable 8k shared memory, no DMA, TC int */
#define ECFGR_IRQOFF 0xC9 /* As above, disable 8390 IRQ */
/* Shared memory management parameters */
#define EL2_SM_START_PG 0x20 /* First page of TX buffer */
#define EL2_SM_STOP_PG 0x40 /* Last page +1 of RX ring */
/* Physical addresses where an Etherlink board can be configured */
#define EL2_BASE_0C8000 0x0C8000
#define EL2_BASE_0CC000 0x0CC000
#define EL2_BASE_0D8000 0x0D8000
#define EL2_BASE_0DC000 0x0DC000
#define inb_el2(dep,reg) (inb((dep)->de_base_port+(reg)))
#define outb_el2(dep,reg,data) (outb((dep)->de_base_port+(reg),(data)))
/** 3c503.h **/