minix3/drivers/net/rtl8139/rtl8139.c

2287 lines
54 KiB
C

/*
* rtl8139.c
*
* This file contains a ethernet device driver for Realtek rtl8139 based
* ethernet cards.
*
* Created: Aug 2003 by Philip Homburg <philip@cs.vu.nl>
* Changes:
* Aug 15, 2004 sync alarms replace watchdogs timers (Jorrit N. Herder)
* May 02, 2004 flag alarms replace micro_elapsed() (Jorrit N. Herder)
*
*/
#define VERBOSE 0 /* Verbose debugging output */
#define RTL8139_FKEY 0 /* Use function key to dump RTL8139 status */
#include "rtl8139.h"
re_t re_state;
static int re_instance;
static unsigned my_inb(u16_t port) {
u32_t value;
int s;
if ((s=sys_inb(port, &value)) !=OK)
printf("RTL8139: warning, sys_inb failed: %d\n", s);
return value;
}
static unsigned my_inw(u16_t port) {
u32_t value;
int s;
if ((s=sys_inw(port, &value)) !=OK)
printf("RTL8139: warning, sys_inw failed: %d\n", s);
return value;
}
static unsigned my_inl(u16_t port) {
u32_t value;
int s;
if ((s=sys_inl(port, &value)) !=OK)
printf("RTL8139: warning, sys_inl failed: %d\n", s);
return value;
}
#define rl_inb(port, offset) (my_inb((port) + (offset)))
#define rl_inw(port, offset) (my_inw((port) + (offset)))
#define rl_inl(port, offset) (my_inl((port) + (offset)))
static void my_outb(u16_t port, u8_t value) {
int s;
if ((s=sys_outb(port, value)) !=OK)
printf("RTL8139: warning, sys_outb failed: %d\n", s);
}
static void my_outw(u16_t port, u16_t value) {
int s;
if ((s=sys_outw(port, value)) !=OK)
printf("RTL8139: warning, sys_outw failed: %d\n", s);
}
static void my_outl(u16_t port, u32_t value) {
int s;
if ((s=sys_outl(port, value)) !=OK)
printf("RTL8139: warning, sys_outl failed: %d\n", s);
}
#define rl_outb(port, offset, value) (my_outb((port) + (offset), (value)))
#define rl_outw(port, offset, value) (my_outw((port) + (offset), (value)))
#define rl_outl(port, offset, value) (my_outl((port) + (offset), (value)))
static void rl_init(message *mp);
static void rl_pci_conf(void);
static int rl_probe(re_t *rep, int skip);
static void rl_conf_hw(re_t *rep);
static void rl_init_buf(re_t *rep);
static void rl_init_hw(re_t *rep);
static void rl_reset_hw(re_t *rep);
static void rl_confaddr(re_t *rep);
static void rl_rec_mode(re_t *rep);
static void rl_readv_s(const message *mp, int from_int);
static void rl_writev_s(const message *mp, int from_int);
static void rl_check_ints(re_t *rep);
static void rl_report_link(re_t *rep);
static void mii_print_techab(u16_t techab);
static void mii_print_stat_speed(u16_t stat, u16_t extstat);
static void rl_clear_rx(re_t *rep);
static void rl_do_reset(re_t *rep);
static void rl_getstat_s(message *mp);
static void reply(re_t *rep);
static void mess_reply(message *req, message *reply);
static void check_int_events(void);
static void do_hard_int(void);
static void rtl8139_dump(message *m);
#if 0
static void dump_phy(re_t *rep);
#endif
static int rl_handler(re_t *rep);
static void rl_watchdog_f(minix_timer_t *tp);
static void tell_dev(vir_bytes start, size_t size, int pci_bus, int
pci_dev, int pci_func);
/* The message used in the main loop is made global, so that rl_watchdog_f()
* can change its message type to fake an interrupt message.
*/
static message m;
static int int_event_check; /* set to TRUE if events arrived */
static u32_t system_hz;
/* SEF functions and variables. */
static void sef_local_startup(void);
static int sef_cb_init_fresh(int type, sef_init_info_t *info);
static void sef_cb_signal_handler(int signo);
EXTERN int sef_cb_lu_prepare(int state);
EXTERN int sef_cb_lu_state_isvalid(int state);
EXTERN void sef_cb_lu_state_dump(int state);
/*===========================================================================*
* main *
*===========================================================================*/
int main(int argc, char *argv[])
{
int r;
int ipc_status;
/* SEF local startup. */
env_setargs(argc, argv);
sef_local_startup();
while (TRUE)
{
if ((r= netdriver_receive(ANY, &m, &ipc_status)) != OK)
panic("netdriver_receive failed: %d", r);
if (is_ipc_notify(ipc_status)) {
switch (_ENDPOINT_P(m.m_source)) {
case CLOCK:
/*
* Under MINIX, synchronous alarms are
* used instead of watchdog functions.
* The approach is very different: MINIX
* VMD timeouts are handled within the
* kernel (the watchdog is executed by
* CLOCK), and notify() the driver in
* some cases. MINIX timeouts result in
* a SYN_ALARM message to the driver and
* thus are handled where they should be
* handled. Locally, watchdog functions
* are used again.
*/
rl_watchdog_f(NULL);
break;
case HARDWARE:
do_hard_int();
if (int_event_check)
check_int_events();
break ;
case TTY_PROC_NR:
rtl8139_dump(&m);
break;
default:
panic("illegal notify from: %d",
m.m_source);
}
/* done, get nwe message */
continue;
}
switch (m.m_type)
{
case DL_WRITEV_S: rl_writev_s(&m, FALSE); break;
case DL_READV_S: rl_readv_s(&m, FALSE); break;
case DL_CONF: rl_init(&m); break;
case DL_GETSTAT_S: rl_getstat_s(&m); break;
default:
panic("illegal message: %d", m.m_type);
}
}
}
/*===========================================================================*
* sef_local_startup *
*===========================================================================*/
static void sef_local_startup()
{
/* Register init callbacks. */
sef_setcb_init_fresh(sef_cb_init_fresh);
sef_setcb_init_lu(sef_cb_init_fresh);
sef_setcb_init_restart(sef_cb_init_fresh);
/* Register live update callbacks. */
sef_setcb_lu_prepare(sef_cb_lu_prepare);
sef_setcb_lu_state_isvalid(sef_cb_lu_state_isvalid);
sef_setcb_lu_state_dump(sef_cb_lu_state_dump);
/* Register signal callbacks. */
sef_setcb_signal_handler(sef_cb_signal_handler);
/* Let SEF perform startup. */
sef_startup();
}
/*===========================================================================*
* sef_cb_init_fresh *
*===========================================================================*/
static int sef_cb_init_fresh(int type, sef_init_info_t *UNUSED(info))
{
/* Initialize the rtl8139 driver. */
long v;
#if RTL8139_FKEY
int r, fkeys, sfkeys;
#endif
system_hz = sys_hz();
v = 0;
(void) env_parse("instance", "d", 0, &v, 0, 255);
re_instance = (int) v;
#if RTL8139_FKEY
/* Observe some function key for debug dumps. */
fkeys = sfkeys = 0; bit_set(sfkeys, 9);
if ((r=fkey_map(&fkeys, &sfkeys)) != OK)
printf("Warning: RTL8139 couldn't observe Shift+F9 key: %d\n",r);
#endif
/* Claim buffer memory now. */
rl_init_buf(&re_state);
/* Announce we are up! */
netdriver_announce();
return(OK);
}
/*===========================================================================*
* sef_cb_signal_handler *
*===========================================================================*/
static void sef_cb_signal_handler(int signo)
{
re_t *rep;
/* Only check for termination signal, ignore anything else. */
if (signo != SIGTERM) return;
rep = &re_state;
if (rep->re_mode == REM_ENABLED)
rl_outb(rep->re_base_port, RL_CR, 0);
exit(0);
}
/*===========================================================================*
* check_int_events *
*===========================================================================*/
static void check_int_events(void)
{
re_t *rep;
rep= &re_state;
if (rep->re_mode != REM_ENABLED)
return;
if (!rep->re_got_int)
return;
rep->re_got_int= 0;
assert(rep->re_flags & REF_ENABLED);
rl_check_ints(rep);
}
/*===========================================================================*
* rtl8139_dump *
*===========================================================================*/
static void rtl8139_dump(m)
message *m; /* pointer to request message */
{
re_t *rep;
rep= &re_state;
printf("\n");
if (rep->re_mode == REM_DISABLED)
printf("Realtek RTL 8139 instance %d is disabled\n",
re_instance);
if (rep->re_mode != REM_ENABLED)
return;
printf("Realtek RTL 8139 statistics of instance %d:\n", re_instance);
printf("recvErr :%8ld\t", rep->re_stat.ets_recvErr);
printf("sendErr :%8ld\t", rep->re_stat.ets_sendErr);
printf("OVW :%8ld\n", rep->re_stat.ets_OVW);
printf("CRCerr :%8ld\t", rep->re_stat.ets_CRCerr);
printf("frameAll :%8ld\t", rep->re_stat.ets_frameAll);
printf("missedP :%8ld\n", rep->re_stat.ets_missedP);
printf("packetR :%8ld\t", rep->re_stat.ets_packetR);
printf("packetT :%8ld\t", rep->re_stat.ets_packetT);
printf("transDef :%8ld\n", rep->re_stat.ets_transDef);
printf("collision :%8ld\t", rep->re_stat.ets_collision);
printf("transAb :%8ld\t", rep->re_stat.ets_transAb);
printf("carrSense :%8ld\n", rep->re_stat.ets_carrSense);
printf("fifoUnder :%8ld\t", rep->re_stat.ets_fifoUnder);
printf("fifoOver :%8ld\t", rep->re_stat.ets_fifoOver);
printf("CDheartbeat:%8ld\n", rep->re_stat.ets_CDheartbeat);
printf("OWC :%8ld\t", rep->re_stat.ets_OWC);
printf("re_flags = 0x%x\n", rep->re_flags);
printf("TSAD: 0x%04x, TSD: 0x%08x, 0x%08x, 0x%08x, 0x%08x\n",
rl_inw(rep->re_base_port, RL_TSAD),
rl_inl(rep->re_base_port, RL_TSD0+0*4),
rl_inl(rep->re_base_port, RL_TSD0+1*4),
rl_inl(rep->re_base_port, RL_TSD0+2*4),
rl_inl(rep->re_base_port, RL_TSD0+3*4));
printf("tx_head %d, tx_tail %d, busy: %d %d %d %d\n",
rep->re_tx_head, rep->re_tx_tail,
rep->re_tx[0].ret_busy, rep->re_tx[1].ret_busy,
rep->re_tx[2].ret_busy, rep->re_tx[3].ret_busy);
}
/*===========================================================================*
* rl_init *
*===========================================================================*/
static void rl_init(mp)
message *mp;
{
static int first_time= 1;
re_t *rep;
message reply_mess;
if (first_time)
{
first_time= 0;
rl_pci_conf(); /* Configure PCI devices. */
/* Use a synchronous alarm instead of a watchdog timer. */
sys_setalarm(system_hz, 0);
}
rep= &re_state;
if (rep->re_mode == REM_DISABLED)
{
/* This is the default, try to (re)locate the device. */
rl_conf_hw(rep);
if (rep->re_mode == REM_DISABLED)
{
/* Probe failed, or the device is configured off. */
reply_mess.m_type= DL_CONF_REPLY;
reply_mess.m_netdrv_net_dl_conf.stat= ENXIO;
mess_reply(mp, &reply_mess);
return;
}
if (rep->re_mode == REM_ENABLED)
rl_init_hw(rep);
#if VERBOSE /* load silently ... can always check status later */
rl_report_link(rep);
#endif
}
assert(rep->re_mode == REM_ENABLED);
assert(rep->re_flags & REF_ENABLED);
rep->re_flags &= ~(REF_PROMISC | REF_MULTI | REF_BROAD);
if (mp->m_net_netdrv_dl_conf.mode & DL_PROMISC_REQ)
rep->re_flags |= REF_PROMISC;
if (mp->m_net_netdrv_dl_conf.mode & DL_MULTI_REQ)
rep->re_flags |= REF_MULTI;
if (mp->m_net_netdrv_dl_conf.mode & DL_BROAD_REQ)
rep->re_flags |= REF_BROAD;
rl_rec_mode(rep);
reply_mess.m_type = DL_CONF_REPLY;
reply_mess.m_netdrv_net_dl_conf.stat = OK;
memcpy(reply_mess.m_netdrv_net_dl_conf.hw_addr,
rep->re_address.ea_addr,
sizeof(reply_mess.m_netdrv_net_dl_conf.hw_addr));
mess_reply(mp, &reply_mess);
}
/*===========================================================================*
* rl_pci_conf *
*===========================================================================*/
static void rl_pci_conf()
{
re_t *rep;
rep= &re_state;
strlcpy(rep->re_name, "rtl8139#0", sizeof(rep->re_name));
rep->re_name[8] += re_instance;
rep->re_seen= FALSE;
pci_init();
if (rl_probe(rep, re_instance))
rep->re_seen= TRUE;
}
/*===========================================================================*
* rl_probe *
*===========================================================================*/
static int rl_probe(rep, skip)
re_t *rep;
int skip;
{
int r, devind;
u16_t vid, did;
u32_t bar;
u8_t ilr;
#if VERBOSE
char *dname;
#endif
r= pci_first_dev(&devind, &vid, &did);
if (r == 0)
return 0;
while (skip--)
{
r= pci_next_dev(&devind, &vid, &did);
if (!r)
return 0;
}
#if VERBOSE /* stay silent at startup, can always get status later */
dname= pci_dev_name(vid, did);
if (!dname)
dname= "unknown device";
printf("%s: ", rep->re_name);
printf("%s (%x/%x) at %s\n", dname, vid, did, pci_slot_name(devind));
#endif
pci_reserve(devind);
/* printf("cr = 0x%x\n", pci_attr_r16(devind, PCI_CR)); */
bar= pci_attr_r32(devind, PCI_BAR) & 0xffffffe0;
if (bar < 0x400) {
panic("base address is not properly configured");
}
rep->re_base_port= bar;
ilr= pci_attr_r8(devind, PCI_ILR);
rep->re_irq= ilr;
if (debug)
{
printf("%s: using I/O address 0x%lx, IRQ %d\n",
rep->re_name, (unsigned long)bar, ilr);
}
return TRUE;
}
/*===========================================================================*
* rl_conf_hw *
*===========================================================================*/
static void rl_conf_hw(rep)
re_t *rep;
{
static eth_stat_t empty_stat = {0, 0, 0, 0, 0, 0 /* ,... */ };
rep->re_mode= REM_DISABLED; /* Superfluous */
if (rep->re_seen)
{
/* PCI device is present */
rep->re_mode= REM_ENABLED;
}
if (rep->re_mode != REM_ENABLED)
return;
rep->re_flags= REF_EMPTY;
rep->re_link_up= -1; /* Unknown */
rep->re_got_int= 0;
rep->re_send_int= 0;
rep->re_report_link= 0;
rep->re_clear_rx= 0;
rep->re_need_reset= 0;
rep->re_tx_alive= 0;
rep->re_read_s= 0;
rep->re_tx_head= 0;
rep->re_tx_tail= 0;
rep->re_ertxth= RL_TSD_ERTXTH_8;
rep->re_stat= empty_stat;
}
/*===========================================================================*
* rl_init_buf *
*===========================================================================*/
static void rl_init_buf(rep)
re_t *rep;
{
size_t rx_bufsize, tx_bufsize, tot_bufsize;
phys_bytes buf;
char *mallocbuf;
int i, off;
/* Allocate receive and transmit buffers */
tx_bufsize= ETH_MAX_PACK_SIZE_TAGGED;
if (tx_bufsize % 4)
tx_bufsize += 4-(tx_bufsize % 4); /* Align */
rx_bufsize= RX_BUFSIZE;
tot_bufsize= N_TX_BUF*tx_bufsize + rx_bufsize;
if (tot_bufsize % 4096)
tot_bufsize += 4096-(tot_bufsize % 4096);
#define BUF_ALIGNMENT (64*1024)
if(!(mallocbuf = alloc_contig(BUF_ALIGNMENT + tot_bufsize, 0, &buf))) {
panic("Couldn't allocate kernel buffer");
}
/* click-align mallocced buffer. this is what we used to get
* from kmalloc() too.
*/
if((off = buf % BUF_ALIGNMENT)) {
mallocbuf += BUF_ALIGNMENT - off;
buf += BUF_ALIGNMENT - off;
}
tell_dev((vir_bytes)mallocbuf, tot_bufsize, 0, 0, 0);
for (i= 0; i<N_TX_BUF; i++)
{
rep->re_tx[i].ret_buf= buf;
rep->re_tx[i].v_ret_buf= mallocbuf;
buf += tx_bufsize;
mallocbuf += tx_bufsize;
}
rep->re_rx_buf= buf;
rep->v_re_rx_buf= mallocbuf;
}
/*===========================================================================*
* rl_init_hw *
*===========================================================================*/
static void rl_init_hw(rep)
re_t *rep;
{
int s, i;
rep->re_flags = REF_EMPTY;
rep->re_flags |= REF_ENABLED;
/* Set the interrupt handler. The policy is to only send HARD_INT
* notifications. Don't reenable interrupts automatically. The id
* that is passed back is the interrupt line number.
*/
rep->re_hook_id = rep->re_irq;
if ((s=sys_irqsetpolicy(rep->re_irq, 0, &rep->re_hook_id)) != OK)
printf("RTL8139: error, couldn't set IRQ policy: %d\n", s);
rl_reset_hw(rep);
if ((s=sys_irqenable(&rep->re_hook_id)) != OK)
printf("RTL8139: error, couldn't enable interrupts: %d\n", s);
#if VERBOSE /* stay silent during startup, can always get status later */
if (rep->re_model) {
printf("%s: model %s\n", rep->re_name, rep->re_model);
} else
{
printf("%s: unknown model 0x%08x\n",
rep->re_name,
rl_inl(rep->re_base_port, RL_TCR) &
(RL_TCR_HWVER_AM | RL_TCR_HWVER_BM));
}
#endif
rl_confaddr(rep);
if (debug)
{
printf("%s: Ethernet address ", rep->re_name);
for (i= 0; i < 6; i++)
{
printf("%x%c", rep->re_address.ea_addr[i],
i < 5 ? ':' : '\n');
}
}
}
/*===========================================================================*
* rl_reset_hw *
*===========================================================================*/
static void rl_reset_hw(rep)
re_t *rep;
{
port_t port;
u32_t t;
phys_bytes bus_buf;
int i;
port= rep->re_base_port;
#if 0
/* Reset the PHY */
rl_outb(port, RL_BMCR, MII_CTRL_RST);
SPIN_UNTIL(!(rl_inb(port, RL_BMCR) & MII_CTRL_RST), 1000000);
if (rl_inb(port, RL_BMCR) & MII_CTRL_RST)
panic("reset PHY failed to complete");
#endif
/* Reset the device */
#if VERBOSE
printf("rl_reset_hw: (before reset) port = 0x%x, RL_CR = 0x%x\n",
port, rl_inb(port, RL_CR));
#endif
rl_outb(port, RL_CR, RL_CR_RST);
SPIN_UNTIL(!(rl_inb(port, RL_CR) & RL_CR_RST), 1000000);
#if VERBOSE
printf("rl_reset_hw: (after reset) port = 0x%x, RL_CR = 0x%x\n",
port, rl_inb(port, RL_CR));
#endif
if (rl_inb(port, RL_CR) & RL_CR_RST)
printf("rtl8139: reset failed to complete");
t= rl_inl(port, RL_TCR);
switch(t & (RL_TCR_HWVER_AM | RL_TCR_HWVER_BM))
{
case RL_TCR_HWVER_RTL8139: rep->re_model= "RTL8139"; break;
case RL_TCR_HWVER_RTL8139A: rep->re_model= "RTL8139A"; break;
case RL_TCR_HWVER_RTL8139AG:
rep->re_model= "RTL8139A-G / RTL8139C";
break;
case RL_TCR_HWVER_RTL8139B:
rep->re_model= "RTL8139B / RTL8130";
break;
case RL_TCR_HWVER_RTL8100: rep->re_model= "RTL8100"; break;
case RL_TCR_HWVER_RTL8100B:
rep->re_model= "RTL8100B/RTL8139D";
break;
case RL_TCR_HWVER_RTL8139CP: rep->re_model= "RTL8139C+"; break;
case RL_TCR_HWVER_RTL8101: rep->re_model= "RTL8101"; break;
default:
rep->re_model= NULL;
break;
}
#if 0
printf("REVID: 0x%02x\n", rl_inb(port, RL_REVID));
#endif
/* Intialize Rx */
/* Should init multicast mask */
#if 0
08-0f R/W MAR[0-7] multicast
#endif
bus_buf= vm_1phys2bus(rep->re_rx_buf);
rl_outl(port, RL_RBSTART, bus_buf);
/* Initialize Tx */
for (i= 0; i<N_TX_BUF; i++)
{
rep->re_tx[i].ret_busy= FALSE;
bus_buf= vm_1phys2bus(rep->re_tx[i].ret_buf);
rl_outl(port, RL_TSAD0+i*4, bus_buf);
t= rl_inl(port, RL_TSD0+i*4);
assert(t & RL_TSD_OWN);
}
#if 0
dump_phy(rep);
#endif
t= rl_inw(port, RL_IMR);
rl_outw(port, RL_IMR, t | (RL_IMR_SERR | RL_IMR_TIMEOUT |
RL_IMR_LENCHG));
t= rl_inw(port, RL_IMR);
rl_outw(port, RL_IMR, t | (RL_IMR_FOVW | RL_IMR_PUN |
RL_IMR_RXOVW | RL_IMR_RER | RL_IMR_ROK));
t= rl_inw(port, RL_IMR);
rl_outw(port, RL_IMR, t | (RL_IMR_TER | RL_IMR_TOK));
t= rl_inb(port, RL_CR);
rl_outb(port, RL_CR, t | RL_CR_RE);
t= rl_inb(port, RL_CR);
rl_outb(port, RL_CR, t | RL_CR_TE);
rl_outl(port, RL_RCR, RX_BUFBITS);
t= rl_inl(port, RL_TCR);
rl_outl(port, RL_TCR, t | RL_TCR_IFG_STD);
}
/*===========================================================================*
* rl_confaddr *
*===========================================================================*/
static void rl_confaddr(rep)
re_t *rep;
{
static char eakey[]= RL_ENVVAR "#_EA";
static char eafmt[]= "x:x:x:x:x:x";
int i;
port_t port;
u32_t w;
long v;
/* User defined ethernet address? */
eakey[sizeof(RL_ENVVAR)-1]= '0' + re_instance;
port= rep->re_base_port;
for (i= 0; i < 6; i++)
{
if (env_parse(eakey, eafmt, i, &v, 0x00L, 0xFFL) != EP_SET)
break;
rep->re_address.ea_addr[i]= v;
}
if (i != 0 && i != 6) env_panic(eakey); /* It's all or nothing */
/* Should update ethernet address in hardware */
if (i == 6)
{
port= rep->re_base_port;
rl_outb(port, RL_9346CR, RL_9346CR_EEM_CONFIG);
w= 0;
for (i= 0; i<4; i++)
w |= (rep->re_address.ea_addr[i] << (i*8));
rl_outl(port, RL_IDR, w);
w= 0;
for (i= 4; i<6; i++)
w |= (rep->re_address.ea_addr[i] << ((i-4)*8));
rl_outl(port, RL_IDR+4, w);
rl_outb(port, RL_9346CR, RL_9346CR_EEM_NORMAL);
}
/* Get ethernet address */
for (i= 0; i<6; i++)
rep->re_address.ea_addr[i]= rl_inb(port, RL_IDR+i);
}
/*===========================================================================*
* rl_rec_mode *
*===========================================================================*/
static void rl_rec_mode(rep)
re_t *rep;
{
port_t port;
u32_t rcr;
port= rep->re_base_port;
rcr= rl_inl(port, RL_RCR);
rcr &= ~(RL_RCR_AB|RL_RCR_AM|RL_RCR_APM|RL_RCR_AAP);
if (rep->re_flags & REF_PROMISC)
rcr |= RL_RCR_AB | RL_RCR_AM | RL_RCR_AAP;
if (rep->re_flags & REF_BROAD)
rcr |= RL_RCR_AB;
if (rep->re_flags & REF_MULTI)
rcr |= RL_RCR_AM;
rcr |= RL_RCR_APM;
rl_outl(port, RL_RCR, rcr);
}
/*===========================================================================*
* rl_readv_s *
*===========================================================================*/
static void rl_readv_s(const message *mp, int from_int)
{
int i, j, n, o, s, s1, count, size;
port_t port;
unsigned amount, totlen, packlen;
u16_t d_start, d_end;
u32_t l, rxstat = 0x12345678;
re_t *rep;
iovec_s_t *iovp;
int cps;
int iov_offset = 0;
rep= &re_state;
rep->re_client= mp->m_source;
count = mp->m_net_netdrv_dl_readv_s.count;
if (rep->re_clear_rx)
goto suspend; /* Buffer overflow */
assert(rep->re_mode == REM_ENABLED);
assert(rep->re_flags & REF_ENABLED);
port= rep->re_base_port;
/* Assume that the RL_CR_BUFE check was been done by rl_checks_ints
*/
if (!from_int && (rl_inb(port, RL_CR) & RL_CR_BUFE))
{
/* Receive buffer is empty, suspend */
goto suspend;
}
d_start= rl_inw(port, RL_CAPR) + RL_CAPR_DATA_OFF;
d_end= rl_inw(port, RL_CBR) % RX_BUFSIZE;
#if RX_BUFSIZE <= USHRT_MAX
if (d_start >= RX_BUFSIZE)
{
printf("rl_readv: strange value in RL_CAPR: 0x%x\n",
rl_inw(port, RL_CAPR));
d_start %= RX_BUFSIZE;
}
#endif
if (d_end > d_start)
amount= d_end-d_start;
else
amount= d_end+RX_BUFSIZE - d_start;
rxstat = *(u32_t *) (rep->v_re_rx_buf + d_start);
if (rep->re_clear_rx)
{
#if 0
printf("rl_readv: late buffer overflow\n");
#endif
goto suspend; /* Buffer overflow */
}
/* Should convert from little endian to host byte order */
if (!(rxstat & RL_RXS_ROK))
{
printf("rxstat = 0x%08x\n", rxstat);
printf("d_start: 0x%x, d_end: 0x%x, rxstat: 0x%x\n",
d_start, d_end, rxstat);
panic("received packet not OK");
}
totlen= (rxstat >> RL_RXS_LEN_S);
if (totlen < 8 || totlen > 2*ETH_MAX_PACK_SIZE)
{
/* Someting went wrong */
printf(
"rl_readv: bad length (%u) in status 0x%08x at offset 0x%x\n",
totlen, rxstat, d_start);
printf(
"d_start: 0x%x, d_end: 0x%x, totlen: %d, rxstat: 0x%x\n",
d_start, d_end, totlen, rxstat);
panic(NULL);
}
#if 0
printf("d_start: 0x%x, d_end: 0x%x, totlen: %d, rxstat: 0x%x\n",
d_start, d_end, totlen, rxstat);
#endif
if (totlen+4 > amount)
{
printf("rl_readv: packet not yet ready\n");
goto suspend;
}
/* Should subtract the CRC */
packlen= totlen - ETH_CRC_SIZE;
size= 0;
o= d_start+4;
for (i= 0; i<count; i += IOVEC_NR,
iov_offset += IOVEC_NR * sizeof(rep->re_iovec_s[0]))
{
n= IOVEC_NR;
if (i+n > count)
n= count-i;
cps = sys_safecopyfrom(mp->m_source,
mp->m_net_netdrv_dl_readv_s.grant, iov_offset,
(vir_bytes) rep->re_iovec_s,
n * sizeof(rep->re_iovec_s[0]));
if (cps != OK) {
panic("rl_readv_s: sys_safecopyfrom failed: %d",
cps);
}
for (j= 0, iovp= rep->re_iovec_s; j<n; j++, iovp++)
{
s= iovp->iov_size;
if (size + s > packlen)
{
assert(packlen > size);
s= packlen-size;
}
#if 0
if (sys_umap(mp->m_source, D, iovp->iov_addr, s, &dst_phys) != OK)
panic("umap_local failed");
#endif
if (o >= RX_BUFSIZE)
{
o -= RX_BUFSIZE;
assert(o < RX_BUFSIZE);
}
if (o+s > RX_BUFSIZE)
{
assert(o<RX_BUFSIZE);
s1= RX_BUFSIZE-o;
cps = sys_safecopyto(mp->m_source,
iovp->iov_grant, 0,
(vir_bytes) rep->v_re_rx_buf+o, s1);
if (cps != OK) {
panic("rl_readv_s: sys_safecopyto failed: %d",
cps);
}
cps = sys_safecopyto(mp->m_source,
iovp->iov_grant, s1,
(vir_bytes) rep->v_re_rx_buf, s-s1);
if (cps != OK) {
panic("rl_readv_s: sys_safecopyto failed: %d", cps);
}
}
else
{
cps = sys_safecopyto(mp->m_source,
iovp->iov_grant, 0,
(vir_bytes) rep->v_re_rx_buf+o, s);
if (cps != OK)
panic("rl_readv_s: sys_safecopyto failed: %d", cps);
}
size += s;
if (size == packlen)
break;
o += s;
}
if (size == packlen)
break;
}
if (size < packlen)
{
assert(0);
}
if (rep->re_clear_rx)
{
/* For some reason the receiver FIFO is not stopped when
* the buffer is full.
*/
#if 0
printf("rl_readv: later buffer overflow\n");
#endif
goto suspend; /* Buffer overflow */
}
rep->re_stat.ets_packetR++;
rep->re_read_s= packlen;
rep->re_flags= (rep->re_flags & ~REF_READING) | REF_PACK_RECV;
/* Avoid overflow in 16-bit computations */
l= d_start;
l += totlen+4;
l= (l+3) & ~3; /* align */
if (l >= RX_BUFSIZE)
{
l -= RX_BUFSIZE;
assert(l < RX_BUFSIZE);
}
rl_outw(port, RL_CAPR, l-RL_CAPR_DATA_OFF);
if (!from_int)
reply(rep);
return;
suspend:
if (from_int)
{
assert(rep->re_flags & REF_READING);
/* No need to store any state */
return;
}
rep->re_rx_mess= *mp;
assert(!(rep->re_flags & REF_READING));
rep->re_flags |= REF_READING;
reply(rep);
}
/*===========================================================================*
* rl_writev_s *
*===========================================================================*/
static void rl_writev_s(const message *mp, int from_int)
{
int i, j, n, s, count, size;
int tx_head;
re_t *rep;
iovec_s_t *iovp;
char *ret;
int cps;
int iov_offset = 0;
rep= &re_state;
rep->re_client= mp->m_source;
count = mp->m_net_netdrv_dl_writev_s.count;
assert(rep->re_mode == REM_ENABLED);
assert(rep->re_flags & REF_ENABLED);
if (from_int)
{
assert(rep->re_flags & REF_SEND_AVAIL);
rep->re_flags &= ~REF_SEND_AVAIL;
rep->re_send_int= FALSE;
rep->re_tx_alive= TRUE;
}
tx_head= rep->re_tx_head;
if (rep->re_tx[tx_head].ret_busy)
{
assert(!(rep->re_flags & REF_SEND_AVAIL));
rep->re_flags |= REF_SEND_AVAIL;
goto suspend;
}
assert(!(rep->re_flags & REF_SEND_AVAIL));
assert(!(rep->re_flags & REF_PACK_SENT));
size= 0;
ret = rep->re_tx[tx_head].v_ret_buf;
for (i= 0; i<count; i += IOVEC_NR,
iov_offset += IOVEC_NR * sizeof(rep->re_iovec_s[0]))
{
n= IOVEC_NR;
if (i+n > count)
n= count-i;
cps = sys_safecopyfrom(mp->m_source,
mp->m_net_netdrv_dl_writev_s.grant, iov_offset,
(vir_bytes) rep->re_iovec_s,
n * sizeof(rep->re_iovec_s[0]));
if (cps != OK) {
panic("rl_writev_s: sys_safecopyfrom failed: %d", cps);
}
for (j= 0, iovp= rep->re_iovec_s; j<n; j++, iovp++)
{
s= iovp->iov_size;
if (size + s > ETH_MAX_PACK_SIZE_TAGGED) {
panic("invalid packet size");
}
cps = sys_safecopyfrom(mp->m_source, iovp->iov_grant,
0, (vir_bytes) ret, s);
if (cps != OK) {
panic("rl_writev_s: sys_safecopyfrom failed: %d", cps);
}
size += s;
ret += s;
}
}
if (size < ETH_MIN_PACK_SIZE)
panic("invalid packet size: %d", size);
rl_outl(rep->re_base_port, RL_TSD0+tx_head*4,
rep->re_ertxth | size);
rep->re_tx[tx_head].ret_busy= TRUE;
if (++tx_head == N_TX_BUF)
tx_head= 0;
assert(tx_head < RL_N_TX);
rep->re_tx_head= tx_head;
rep->re_flags |= REF_PACK_SENT;
/* If the interrupt handler called, don't send a reply. The reply
* will be sent after all interrupts are handled.
*/
if (from_int)
return;
reply(rep);
return;
suspend:
#if 0
printf("rl_writev: head %d, tail %d, busy: %d %d %d %d\n",
tx_head, rep->re_tx_tail,
rep->re_tx[0].ret_busy, rep->re_tx[1].ret_busy,
rep->re_tx[2].ret_busy, rep->re_tx[3].ret_busy);
printf("rl_writev: TSD: 0x%x, 0x%x, 0x%x, 0x%x\n",
rl_inl(rep->re_base_port, RL_TSD0+0*4),
rl_inl(rep->re_base_port, RL_TSD0+1*4),
rl_inl(rep->re_base_port, RL_TSD0+2*4),
rl_inl(rep->re_base_port, RL_TSD0+3*4));
#endif
if (from_int)
panic("should not be sending");
rep->re_tx_mess= *mp;
reply(rep);
}
/*===========================================================================*
* rl_check_ints *
*===========================================================================*/
static void rl_check_ints(rep)
re_t *rep;
{
#if 0
10-1f R/W TSD[0-3] Transmit Status of Descriptor [0-3]
31 R CRS Carrier Sense Lost
30 R TABT Transmit Abort
29 R OWC Out of Window Collision
27-24 R NCC[3-0] Number of Collision Count
23-22 reserved
21-16 R/W ERTXH[5-0] Early Tx Threshold
15 R TOK Transmit OK
14 R TUN Transmit FIFO Underrun
13 R/W OWN OWN
12-0 R/W SIZE Descriptor Size
3e-3f R/W ISR Interrupt Status Register
6 R/W FOVW Fx FIFO Overflow Interrupt
5 R/W PUN/LinkChg Packet Underrun / Link Change Interrupt
3 R/W TER Transmit Error Interrupt
2 R/W TOK Transmit OK Interrupt
3e-3f R/W ISR Interrupt Status Register
15 R/W SERR System Error Interrupt
14 R/W TimeOut Time Out Interrupt
13 R/W LenChg Cable Length Change Interrupt
3e-3f R/W ISR Interrupt Status Register
4 R/W RXOVW Rx Buffer Overflow Interrupt
1 R/W RER Receive Error Interrupt
0 R/W ROK Receive OK Interrupt
4c-4f R/W MPC Missed Packet Counter
60-61 R TSAD Transmit Status of All Descriptors
15-12 R TOK[3-0] TOK bit of Descriptor [3-0]
11-8 R TUN[3-0] TUN bit of Descriptor [3-0]
7-4 R TABT[3-0] TABT bit of Descriptor [3-0]
3-0 R OWN[3-0] OWN bit of Descriptor [3-0]
6c-6d R DIS Disconnect Counter
15-0 R DCNT Disconnect Counter
6e-6f R FCSC False Carrier Sense Counter
15-0 R FCSCNT False Carrier event counter
72-73 R REC RX_ER Counter
15-0 R RXERCNT Received packet counter
#endif
int re_flags;
re_flags= rep->re_flags;
if ((re_flags & REF_READING) &&
!(rl_inb(rep->re_base_port, RL_CR) & RL_CR_BUFE))
{
rl_readv_s(&rep->re_rx_mess, TRUE /* from int */);
}
if (rep->re_clear_rx)
rl_clear_rx(rep);
if (rep->re_need_reset)
rl_do_reset(rep);
if (rep->re_send_int)
{
rl_writev_s(&rep->re_tx_mess, TRUE /* from int */);
}
if (rep->re_report_link)
rl_report_link(rep);
if (rep->re_flags & (REF_PACK_SENT | REF_PACK_RECV))
reply(rep);
}
/*===========================================================================*
* rl_report_link *
*===========================================================================*/
static void rl_report_link(rep)
re_t *rep;
{
port_t port;
u16_t mii_ctrl, mii_status, mii_ana, mii_anlpa, mii_ane, mii_extstat;
u8_t msr;
int f, link_up;
rep->re_report_link= FALSE;
port= rep->re_base_port;
msr= rl_inb(port, RL_MSR);
link_up= !(msr & RL_MSR_LINKB);
rep->re_link_up= link_up;
if (!link_up)
{
printf("%s: link down\n", rep->re_name);
return;
}
mii_ctrl= rl_inw(port, RL_BMCR);
mii_status= rl_inw(port, RL_BMSR);
mii_ana= rl_inw(port, RL_ANAR);
mii_anlpa= rl_inw(port, RL_ANLPAR);
mii_ane= rl_inw(port, RL_ANER);
mii_extstat= 0;
if (mii_ctrl & (MII_CTRL_LB|MII_CTRL_PD|MII_CTRL_ISO))
{
printf("%s: PHY: ", rep->re_name);
f= 1;
if (mii_ctrl & MII_CTRL_LB)
{
printf("loopback mode");
f= 0;
}
if (mii_ctrl & MII_CTRL_PD)
{
if (!f) printf(", ");
f= 0;
printf("powered down");
}
if (mii_ctrl & MII_CTRL_ISO)
{
if (!f) printf(", ");
f= 0;
printf("isolated");
}
printf("\n");
return;
}
if (!(mii_ctrl & MII_CTRL_ANE))
{
printf("%s: manual config: ", rep->re_name);
switch(mii_ctrl & (MII_CTRL_SP_LSB|MII_CTRL_SP_MSB))
{
case MII_CTRL_SP_10: printf("10 Mbps"); break;
case MII_CTRL_SP_100: printf("100 Mbps"); break;
case MII_CTRL_SP_1000: printf("1000 Mbps"); break;
case MII_CTRL_SP_RES: printf("reserved speed"); break;
}
if (mii_ctrl & MII_CTRL_DM)
printf(", full duplex");
else
printf(", half duplex");
printf("\n");
return;
}
if (!debug) goto resspeed;
printf("%s: ", rep->re_name);
mii_print_stat_speed(mii_status, mii_extstat);
printf("\n");
if (!(mii_status & MII_STATUS_ANC))
printf("%s: auto-negotiation not complete\n", rep->re_name);
if (mii_status & MII_STATUS_RF)
printf("%s: remote fault detected\n", rep->re_name);
if (!(mii_status & MII_STATUS_ANA))
{
printf("%s: local PHY has no auto-negotiation ability\n",
rep->re_name);
}
if (!(mii_status & MII_STATUS_LS))
printf("%s: link down\n", rep->re_name);
if (mii_status & MII_STATUS_JD)
printf("%s: jabber condition detected\n", rep->re_name);
if (!(mii_status & MII_STATUS_EC))
{
printf("%s: no extended register set\n", rep->re_name);
goto resspeed;
}
if (!(mii_status & MII_STATUS_ANC))
goto resspeed;
printf("%s: local cap.: ", rep->re_name);
mii_print_techab(mii_ana);
printf("\n");
if (mii_ane & MII_ANE_PDF)
printf("%s: parallel detection fault\n", rep->re_name);
if (!(mii_ane & MII_ANE_LPANA))
{
printf("%s: link-partner does not support auto-negotiation\n",
rep->re_name);
goto resspeed;
}
printf("%s: remote cap.: ", rep->re_name);
mii_print_techab(mii_anlpa);
printf("\n");
resspeed:
printf("%s: ", rep->re_name);
printf("link up at %d Mbps, ", (msr & RL_MSR_SPEED_10) ? 10 : 100);
printf("%s duplex\n", ((mii_ctrl & MII_CTRL_DM) ? "full" : "half"));
}
static void mii_print_techab(u16_t techab)
{
int fs, ft;
if ((techab & MII_ANA_SEL_M) != MII_ANA_SEL_802_3)
{
printf("strange selector 0x%x, value 0x%x",
techab & MII_ANA_SEL_M,
(techab & MII_ANA_TAF_M) >> MII_ANA_TAF_S);
return;
}
fs= 1;
if (techab & (MII_ANA_100T4 | MII_ANA_100TXFD | MII_ANA_100TXHD))
{
printf("100 Mbps: ");
fs= 0;
ft= 1;
if (techab & MII_ANA_100T4)
{
printf("T4");
ft= 0;
}
if (techab & (MII_ANA_100TXFD | MII_ANA_100TXHD))
{
if (!ft)
printf(", ");
ft= 0;
printf("TX-");
switch(techab & (MII_ANA_100TXFD|MII_ANA_100TXHD))
{
case MII_ANA_100TXFD: printf("FD"); break;
case MII_ANA_100TXHD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
}
if (techab & (MII_ANA_10TFD | MII_ANA_10THD))
{
if (!fs)
printf(", ");
printf("10 Mbps: ");
fs= 0;
printf("T-");
switch(techab & (MII_ANA_10TFD|MII_ANA_10THD))
{
case MII_ANA_10TFD: printf("FD"); break;
case MII_ANA_10THD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
if (techab & MII_ANA_PAUSE_SYM)
{
if (!fs)
printf(", ");
fs= 0;
printf("pause(SYM)");
}
if (techab & MII_ANA_PAUSE_ASYM)
{
if (!fs)
printf(", ");
fs= 0;
printf("pause(ASYM)");
}
if (techab & MII_ANA_TAF_RES)
{
if (!fs)
printf(", ");
fs= 0;
printf("0x%x", (techab & MII_ANA_TAF_RES) >> MII_ANA_TAF_S);
}
}
static void mii_print_stat_speed(u16_t stat, u16_t extstat)
{
int fs, ft;
fs= 1;
if (stat & MII_STATUS_EXT_STAT)
{
if (extstat & (MII_ESTAT_1000XFD | MII_ESTAT_1000XHD |
MII_ESTAT_1000TFD | MII_ESTAT_1000THD))
{
printf("1000 Mbps: ");
fs= 0;
ft= 1;
if (extstat & (MII_ESTAT_1000XFD | MII_ESTAT_1000XHD))
{
ft= 0;
printf("X-");
switch(extstat &
(MII_ESTAT_1000XFD|MII_ESTAT_1000XHD))
{
case MII_ESTAT_1000XFD: printf("FD"); break;
case MII_ESTAT_1000XHD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
if (extstat & (MII_ESTAT_1000TFD | MII_ESTAT_1000THD))
{
if (!ft)
printf(", ");
ft= 0;
printf("T-");
switch(extstat &
(MII_ESTAT_1000TFD|MII_ESTAT_1000THD))
{
case MII_ESTAT_1000TFD: printf("FD"); break;
case MII_ESTAT_1000THD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
}
}
if (stat & (MII_STATUS_100T4 |
MII_STATUS_100XFD | MII_STATUS_100XHD |
MII_STATUS_100T2FD | MII_STATUS_100T2HD))
{
if (!fs)
printf(", ");
fs= 0;
printf("100 Mbps: ");
ft= 1;
if (stat & MII_STATUS_100T4)
{
printf("T4");
ft= 0;
}
if (stat & (MII_STATUS_100XFD | MII_STATUS_100XHD))
{
if (!ft)
printf(", ");
ft= 0;
printf("TX-");
switch(stat & (MII_STATUS_100XFD|MII_STATUS_100XHD))
{
case MII_STATUS_100XFD: printf("FD"); break;
case MII_STATUS_100XHD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
if (stat & (MII_STATUS_100T2FD | MII_STATUS_100T2HD))
{
if (!ft)
printf(", ");
ft= 0;
printf("T2-");
switch(stat & (MII_STATUS_100T2FD|MII_STATUS_100T2HD))
{
case MII_STATUS_100T2FD: printf("FD"); break;
case MII_STATUS_100T2HD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
}
if (stat & (MII_STATUS_10FD | MII_STATUS_10HD))
{
if (!fs)
printf(", ");
printf("10 Mbps: ");
fs= 0;
printf("T-");
switch(stat & (MII_STATUS_10FD|MII_STATUS_10HD))
{
case MII_STATUS_10FD: printf("FD"); break;
case MII_STATUS_10HD: printf("HD"); break;
default: printf("FD/HD"); break;
}
}
}
/*===========================================================================*
* rl_clear_rx *
*===========================================================================*/
static void rl_clear_rx(re_t *rep)
{
port_t port;
u8_t cr;
rep->re_clear_rx= FALSE;
port= rep->re_base_port;
/* Reset the receiver */
cr= rl_inb(port, RL_CR);
cr &= ~RL_CR_RE;
rl_outb(port, RL_CR, cr);
SPIN_UNTIL(!(rl_inb(port, RL_CR) & RL_CR_RE), 1000000);
if (rl_inb(port, RL_CR) & RL_CR_RE)
panic("cannot disable receiver");
#if 0
printf("RBSTART = 0x%08x\n", rl_inl(port, RL_RBSTART));
printf("CAPR = 0x%04x\n", rl_inw(port, RL_CAPR));
printf("CBR = 0x%04x\n", rl_inw(port, RL_CBR));
printf("RCR = 0x%08x\n", rl_inl(port, RL_RCR));
#endif
rl_outb(port, RL_CR, cr | RL_CR_RE);
rl_outl(port, RL_RCR, RX_BUFBITS);
rl_rec_mode(rep);
rep->re_stat.ets_missedP++;
}
/*===========================================================================*
* rl_do_reset *
*===========================================================================*/
static void rl_do_reset(rep)
re_t *rep;
{
rep->re_need_reset= FALSE;
rl_reset_hw(rep);
rl_rec_mode(rep);
rep->re_tx_head= 0;
if (rep->re_flags & REF_SEND_AVAIL)
{
rep->re_tx[rep->re_tx_head].ret_busy= FALSE;
rep->re_send_int= TRUE;
}
}
/*===========================================================================*
* rl_getstat_s *
*===========================================================================*/
static void rl_getstat_s(mp)
message *mp;
{
int r;
eth_stat_t stats;
re_t *rep;
rep= &re_state;
assert(rep->re_mode == REM_ENABLED);
assert(rep->re_flags & REF_ENABLED);
stats= rep->re_stat;
r = sys_safecopyto(mp->m_source, mp->m_net_netdrv_dl_getstat_s.grant,
0, (vir_bytes) &stats, sizeof(stats));
if (r != OK)
panic("rl_getstat_s: sys_safecopyto failed: %d", r);
mp->m_type= DL_STAT_REPLY;
r= ipc_send(mp->m_source, mp);
if (r != OK)
panic("rl_getstat_s: ipc_send failed: %d", r);
}
/*===========================================================================*
* reply *
*===========================================================================*/
static void reply(rep)
re_t *rep;
{
message reply;
int flags;
int r;
flags = DL_NOFLAGS;
if (rep->re_flags & REF_PACK_SENT)
flags |= DL_PACK_SEND;
if (rep->re_flags & REF_PACK_RECV)
flags |= DL_PACK_RECV;
reply.m_type = DL_TASK_REPLY;
reply.m_netdrv_net_dl_task.flags = flags;
reply.m_netdrv_net_dl_task.count = rep->re_read_s;
r= ipc_send(rep->re_client, &reply);
if (r < 0) {
printf("RTL8139 tried sending to %d, type %d\n",
rep->re_client, reply.m_type);
panic("ipc_send failed: %d", r);
}
rep->re_read_s = 0;
rep->re_flags &= ~(REF_PACK_SENT | REF_PACK_RECV);
}
/*===========================================================================*
* mess_reply *
*===========================================================================*/
static void mess_reply(req, reply_mess)
message *req;
message *reply_mess;
{
if (ipc_send(req->m_source, reply_mess) != OK)
panic("unable to mess_reply");
}
#if 0
/*===========================================================================*
* dump_phy *
*===========================================================================*/
static void dump_phy(rep)
re_t *rep;
{
port_t port;
u32_t t;
port= rep->re_base_port;
t= rl_inb(port, RL_MSR);
printf("MSR: 0x%02lx\n", t);
if (t & RL_MSR_SPEED_10)
printf("\t10 Mbps\n");
if (t & RL_MSR_LINKB)
printf("\tLink failed\n");
t= rl_inb(port, RL_CONFIG1);
printf("CONFIG1: 0x%02lx\n", t);
t= rl_inb(port, RL_CONFIG3);
printf("CONFIG3: 0x%02lx\n", t);
t= rl_inb(port, RL_CONFIG4);
printf("CONFIG4: 0x%02lx\n", t);
t= rl_inw(port, RL_BMCR);
printf("BMCR (MII_CTRL): 0x%04lx\n", t);
t= rl_inw(port, RL_BMSR);
printf("BMSR:");
if (t & MII_STATUS_100T4)
printf(" 100Base-T4");
if (t & MII_STATUS_100XFD)
printf(" 100Base-X-FD");
if (t & MII_STATUS_100XHD)
printf(" 100Base-X-HD");
if (t & MII_STATUS_10FD)
printf(" 10Mbps-FD");
if (t & MII_STATUS_10HD)
printf(" 10Mbps-HD");
if (t & MII_STATUS_100T2FD)
printf(" 100Base-T2-FD");
if (t & MII_STATUS_100T2HD)
printf(" 100Base-T2-HD");
if (t & MII_STATUS_EXT_STAT)
printf(" Ext-stat");
if (t & MII_STATUS_RES)
printf(" res-0x%lx", t & MII_STATUS_RES);
if (t & MII_STATUS_MFPS)
printf(" MFPS");
if (t & MII_STATUS_ANC)
printf(" ANC");
if (t & MII_STATUS_RF)
printf(" remote-fault");
if (t & MII_STATUS_ANA)
printf(" ANA");
if (t & MII_STATUS_LS)
printf(" Link");
if (t & MII_STATUS_JD)
printf(" Jabber");
if (t & MII_STATUS_EC)
printf(" Extended-capability");
printf("\n");
t= rl_inw(port, RL_ANAR);
printf("ANAR (MII_ANA): 0x%04lx\n", t);
t= rl_inw(port, RL_ANLPAR);
printf("ANLPAR: 0x%04lx\n", t);
t= rl_inw(port, RL_ANER);
printf("ANER (MII_ANE): ");
if (t & MII_ANE_RES)
printf(" res-0x%lx", t & MII_ANE_RES);
if (t & MII_ANE_PDF)
printf(" Par-Detect-Fault");
if (t & MII_ANE_LPNPA)
printf(" LP-Next-Page-Able");
if (t & MII_ANE_NPA)
printf(" Loc-Next-Page-Able");
if (t & MII_ANE_PR)
printf(" Page-Received");
if (t & MII_ANE_LPANA)
printf(" LP-Auto-Neg-Able");
printf("\n");
t= rl_inw(port, RL_NWAYTR);
printf("NWAYTR: 0x%04lx\n", t);
t= rl_inw(port, RL_CSCR);
printf("CSCR: 0x%04lx\n", t);
t= rl_inb(port, RL_CONFIG5);
printf("CONFIG5: 0x%02lx\n", t);
}
#endif
/*===========================================================================*
* do_hard_int *
*===========================================================================*/
static void do_hard_int(void)
{
int s;
/* Run interrupt handler at driver level. */
rl_handler(&re_state);
/* Reenable interrupts for this hook. */
if ((s=sys_irqenable(&re_state.re_hook_id)) != OK)
printf("RTL8139: error, couldn't enable interrupts: %d\n", s);
}
/*===========================================================================*
* rl_handler *
*===========================================================================*/
static int rl_handler(re_t *rep)
{
int i, port, tx_head, tx_tail, link_up;
u16_t isr, tsad;
u32_t tsd, tcr, ertxth;
#if 0
u8_t cr;
#endif
int_event_check = FALSE; /* disable check by default */
port= rep->re_base_port;
/* Ack interrupt */
isr= rl_inw(port, RL_ISR);
rl_outw(port, RL_ISR, isr);
if (isr & RL_IMR_FOVW)
{
isr &= ~RL_IMR_FOVW;
/* Should do anything? */
rep->re_stat.ets_fifoOver++;
}
if (isr & RL_IMR_PUN)
{
isr &= ~RL_IMR_PUN;
/* Either the link status changed or there was a TX fifo
* underrun.
*/
link_up= !(rl_inb(port, RL_MSR) & RL_MSR_LINKB);
if (link_up != rep->re_link_up)
{
rep->re_report_link= TRUE;
rep->re_got_int= TRUE;
int_event_check = TRUE;
}
}
if (isr & RL_IMR_RXOVW)
{
isr &= ~RL_IMR_RXOVW;
/* Clear the receive buffer */
rep->re_clear_rx= TRUE;
rep->re_got_int= TRUE;
int_event_check = TRUE;
}
if (isr & (RL_ISR_RER | RL_ISR_ROK))
{
isr &= ~(RL_ISR_RER | RL_ISR_ROK);
if (!rep->re_got_int && (rep->re_flags & REF_READING))
{
rep->re_got_int= TRUE;
int_event_check = TRUE;
}
}
#if 0
if ((isr & (RL_ISR_TER | RL_ISR_TOK)) &&
(rep->re_flags & REF_SEND_AVAIL) &&
(rep->re_tx[0].ret_busy || rep->re_tx[1].ret_busy ||
rep->re_tx[2].ret_busy || rep->re_tx[3].ret_busy))
{
printf(
"rl_handler, SEND_AVAIL: tx_head %d, tx_tail %d, busy: %d %d %d %d\n",
rep->re_tx_head, rep->re_tx_tail,
rep->re_tx[0].ret_busy, rep->re_tx[1].ret_busy,
rep->re_tx[2].ret_busy, rep->re_tx[3].ret_busy);
printf(
"rl_handler: TSAD: 0x%04x, TSD: 0x%08x, 0x%08x, 0x%08x, 0x%08x\n",
rl_inw(port, RL_TSAD),
rl_inl(port, RL_TSD0+0*4),
rl_inl(port, RL_TSD0+1*4),
rl_inl(port, RL_TSD0+2*4),
rl_inl(port, RL_TSD0+3*4));
}
#endif
if ((isr & (RL_ISR_TER | RL_ISR_TOK)) || 1)
{
isr &= ~(RL_ISR_TER | RL_ISR_TOK);
tsad= rl_inw(port, RL_TSAD);
if (tsad & (RL_TSAD_TABT0|RL_TSAD_TABT1|
RL_TSAD_TABT2|RL_TSAD_TABT3))
{
#if 0
/* Do we need a watch dog? */
/* Just reset the whole chip */
rep->re_need_reset= TRUE;
rep->re_got_int= TRUE;
int_event_check = TRUE;
#elif 0
/* Reset transmitter */
rep->re_stat.ets_transAb++;
cr= rl_inb(port, RL_CR);
cr &= ~RL_CR_TE;
rl_outb(port, RL_CR, cr);
SPIN_UNTIL(!(rl_inb(port, RL_CR) & RL_CR_TE), 1000000);
if (rl_inb(port, RL_CR) & RL_CR_TE) {
panic("cannot disable transmitter");
}
rl_outb(port, RL_CR, cr | RL_CR_TE);
tcr= rl_inl(port, RL_TCR);
rl_outl(port, RL_TCR, tcr | RL_TCR_IFG_STD);
printf("rl_handler: reset after abort\n");
if (rep->re_flags & REF_SEND_AVAIL)
{
printf("rl_handler: REF_SEND_AVAIL\n");
rep->re_send_int= TRUE;
rep->re_got_int= TRUE;
int_event_check = TRUE;
}
for (i= 0; i< N_TX_BUF; i++)
rep->re_tx[i].ret_busy= FALSE;
rep->re_tx_head= 0;
#else
printf("rl_handler, TABT, tasd = 0x%04x\n",
tsad);
/* Find the aborted transmit request */
for (i= 0; i< N_TX_BUF; i++)
{
tsd= rl_inl(port, RL_TSD0+i*4);
if (tsd & RL_TSD_TABT)
break;
}
if (i >= N_TX_BUF)
{
printf(
"rl_handler: can't find aborted TX req.\n");
}
else
{
printf("TSD%d = 0x%04x\n", i, tsd);
/* Set head and tail to this buffer */
rep->re_tx_head= rep->re_tx_tail= i;
}
/* Aborted transmission, just kick the device
* and be done with it.
*/
rep->re_stat.ets_transAb++;
tcr= rl_inl(port, RL_TCR);
rl_outl(port, RL_TCR, tcr | RL_TCR_CLRABT);
#endif
}
/* Transmit completed */
tx_head= rep->re_tx_head;
tx_tail= rep->re_tx_tail;
for (i= 0; i< 2*N_TX_BUF; i++)
{
if (!rep->re_tx[tx_tail].ret_busy)
{
/* Strange, this buffer is not in-use.
* Increment tx_tail until tx_head is
* reached (or until we find a buffer that
* is in-use.
*/
if (tx_tail == tx_head)
break;
if (++tx_tail >= N_TX_BUF)
tx_tail= 0;
assert(tx_tail < RL_N_TX);
rep->re_tx_tail= tx_tail;
continue;
}
tsd= rl_inl(port, RL_TSD0+tx_tail*4);
if (!(tsd & RL_TSD_OWN))
{
/* Buffer is not yet ready */
break;
}
/* Should collect statistics */
if (tsd & RL_TSD_CRS)
rep->re_stat.ets_carrSense++;
if (tsd & RL_TSD_TABT)
{
printf("rl_handler, TABT, TSD%d = 0x%04x\n",
tx_tail, tsd);
assert(0); /* CLRABT is not all that
* effective, why not?
*/
rep->re_stat.ets_transAb++;
tcr= rl_inl(port, RL_TCR);
rl_outl(port, RL_TCR, tcr | RL_TCR_CLRABT);
}
if (tsd & RL_TSD_OWC)
rep->re_stat.ets_OWC++;
if (tsd & RL_TSD_CDH)
rep->re_stat.ets_CDheartbeat++;
/* What about collisions? */
if (tsd & RL_TSD_TOK)
rep->re_stat.ets_packetT++;
else
rep->re_stat.ets_sendErr++;
if (tsd & RL_TSD_TUN)
{
rep->re_stat.ets_fifoUnder++;
/* Increase ERTXTH */
ertxth= tsd + (1 << RL_TSD_ERTXTH_S);
ertxth &= RL_TSD_ERTXTH_M;
if (debug && ertxth > rep->re_ertxth)
{
printf("%s: new ertxth: %d bytes\n",
rep->re_name,
(ertxth >> RL_TSD_ERTXTH_S) *
32);
rep->re_ertxth= ertxth;
}
}
rep->re_tx[tx_tail].ret_busy= FALSE;
#if 0
if (rep->re_flags & REF_SEND_AVAIL)
{
printf("TSD%d: %08lx\n", tx_tail, tsd);
printf(
"rl_handler: head %d, tail %d, busy: %d %d %d %d\n",
tx_head, tx_tail,
rep->re_tx[0].ret_busy, rep->re_tx[1].ret_busy,
rep->re_tx[2].ret_busy, rep->re_tx[3].ret_busy);
}
#endif
if (++tx_tail >= N_TX_BUF)
tx_tail= 0;
assert(tx_tail < RL_N_TX);
rep->re_tx_tail= tx_tail;
if (rep->re_flags & REF_SEND_AVAIL)
{
#if 0
printf("rl_handler: REF_SEND_AVAIL\n");
#endif
rep->re_send_int= TRUE;
if (!rep->re_got_int)
{
rep->re_got_int= TRUE;
int_event_check = TRUE;
}
}
}
assert(i < 2*N_TX_BUF);
}
if (isr)
{
printf("rl_handler: unhandled interrupt: isr = 0x%04x\n",
isr);
}
return 1;
}
/*===========================================================================*
* rl_watchdog_f *
*===========================================================================*/
static void rl_watchdog_f(tp)
minix_timer_t *tp;
{
re_t *rep;
/* Use a synchronous alarm instead of a watchdog timer. */
sys_setalarm(system_hz, 0);
rep= &re_state;
if (rep->re_mode != REM_ENABLED)
return;
if (!(rep->re_flags & REF_SEND_AVAIL))
{
/* Assume that an idle system is alive */
rep->re_tx_alive= TRUE;
return;
}
if (rep->re_tx_alive)
{
rep->re_tx_alive= FALSE;
return;
}
printf("rl_watchdog_f: resetting instance %d\n", re_instance);
printf("TSAD: 0x%04x, TSD: 0x%08x, 0x%08x, 0x%08x, 0x%08x\n",
rl_inw(rep->re_base_port, RL_TSAD),
rl_inl(rep->re_base_port, RL_TSD0+0*4),
rl_inl(rep->re_base_port, RL_TSD0+1*4),
rl_inl(rep->re_base_port, RL_TSD0+2*4),
rl_inl(rep->re_base_port, RL_TSD0+3*4));
printf("tx_head %d, tx_tail %d, busy: %d %d %d %d\n",
rep->re_tx_head, rep->re_tx_tail,
rep->re_tx[0].ret_busy, rep->re_tx[1].ret_busy,
rep->re_tx[2].ret_busy, rep->re_tx[3].ret_busy);
rep->re_need_reset= TRUE;
rep->re_got_int= TRUE;
check_int_events();
}
#if 0
static void rtl_init(struct dpeth *dep);
static u16_t get_ee_word(dpeth_t *dep, int a);
static void ee_wen(dpeth_t *dep);
static void set_ee_word(dpeth_t *dep, int a, u16_t w);
static void ee_wds(dpeth_t *dep);
static void rtl_init(dep)
dpeth_t *dep;
{
u8_t reg_a, reg_b, cr, config0, config2, config3;
int i;
char val[128];
printf("rtl_init called\n");
ne_init(dep);
/* ID */
outb_reg0(dep, DP_CR, CR_PS_P0);
reg_a = inb_reg0(dep, DP_DUM1);
reg_b = inb_reg0(dep, DP_DUM2);
printf("rtl_init: '%c', '%c'\n", reg_a, reg_b);
outb_reg0(dep, DP_CR, CR_PS_P3);
config0 = inb_reg3(dep, 3);
config2 = inb_reg3(dep, 5);
config3 = inb_reg3(dep, 6);
outb_reg0(dep, DP_CR, CR_PS_P0);
printf("rtl_init: config 0/2/3 = %x/%x/%x\n",
config0, config2, config3);
if (0 == sys_getkenv("RTL8029FD",9+1, val, sizeof(val)))
{
printf("rtl_init: setting full-duplex mode\n");
outb_reg0(dep, DP_CR, CR_PS_P3);
cr= inb_reg3(dep, 1);
outb_reg3(dep, 1, cr | 0xc0);
outb_reg3(dep, 6, config3 | 0x40);
config3 = inb_reg3(dep, 6);
config2= inb_reg3(dep, 5);
outb_reg3(dep, 5, config2 | 0x20);
config2= inb_reg3(dep, 5);
outb_reg3(dep, 1, cr);
outb_reg0(dep, DP_CR, CR_PS_P0);
printf("rtl_init: config 2 = %x\n", config2);
printf("rtl_init: config 3 = %x\n", config3);
}
for (i= 0; i<64; i++)
printf("%x ", get_ee_word(dep, i));
printf("\n");
if (0 == sys_getkenv("RTL8029MN",9+1, val, sizeof(val)))
{
ee_wen(dep);
set_ee_word(dep, 0x78/2, 0x10ec);
set_ee_word(dep, 0x7A/2, 0x8029);
set_ee_word(dep, 0x7C/2, 0x10ec);
set_ee_word(dep, 0x7E/2, 0x8029);
ee_wds(dep);
assert(get_ee_word(dep, 0x78/2) == 0x10ec);
assert(get_ee_word(dep, 0x7A/2) == 0x8029);
assert(get_ee_word(dep, 0x7C/2) == 0x10ec);
assert(get_ee_word(dep, 0x7E/2) == 0x8029);
}
if (0 == sys_getkenv("RTL8029XXX",10+1, val, sizeof(val)))
{
ee_wen(dep);
set_ee_word(dep, 0x76/2, 0x8029);
ee_wds(dep);
assert(get_ee_word(dep, 0x76/2) == 0x8029);
}
}
static u16_t get_ee_word(dep, a)
dpeth_t *dep;
int a;
{
int b, i, cmd;
u16_t w;
outb_reg0(dep, DP_CR, CR_PS_P3); /* Bank 3 */
/* Switch to 9346 mode and enable CS */
outb_reg3(dep, 1, 0x80 | 0x8);
cmd= 0x180 | (a & 0x3f); /* 1 1 0 a5 a4 a3 a2 a1 a0 */
for (i= 8; i >= 0; i--)
{
b= (cmd & (1 << i));
b= (b ? 2 : 0);
/* Cmd goes out on the rising edge of the clock */
outb_reg3(dep, 1, 0x80 | 0x8 | b);
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4 | b);
}
outb_reg3(dep, 1, 0x80 | 0x8); /* End of cmd */
w= 0;
for (i= 0; i<16; i++)
{
w <<= 1;
/* Data is shifted out on the rising edge. Read at the
* falling edge.
*/
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4);
outb_reg3(dep, 1, 0x80 | 0x8 | b);
b= inb_reg3(dep, 1);
w |= (b & 1);
}
outb_reg3(dep, 1, 0x80); /* drop CS */
outb_reg3(dep, 1, 0x00); /* back to normal */
outb_reg0(dep, DP_CR, CR_PS_P0); /* back to bank 0 */
return w;
}
static void ee_wen(dep)
dpeth_t *dep;
{
int b, i, cmd;
u16_t w;
outb_reg0(dep, DP_CR, CR_PS_P3); /* Bank 3 */
/* Switch to 9346 mode and enable CS */
outb_reg3(dep, 1, 0x80 | 0x8);
cmd= 0x130; /* 1 0 0 1 1 x x x x */
for (i= 8; i >= 0; i--)
{
b= (cmd & (1 << i));
b= (b ? 2 : 0);
/* Cmd goes out on the rising edge of the clock */
outb_reg3(dep, 1, 0x80 | 0x8 | b);
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4 | b);
}
outb_reg3(dep, 1, 0x80 | 0x8); /* End of cmd */
outb_reg3(dep, 1, 0x80); /* Drop CS */
/* micro_delay(1); */ /* Is this required? */
}
static void set_ee_word(dpeth_t *dep, int a, u16_t w)
dpeth_t *dep;
int a;
u16_t w;
{
int b, i, cmd;
outb_reg3(dep, 1, 0x80 | 0x8); /* Set CS */
cmd= 0x140 | (a & 0x3f); /* 1 0 1 a5 a4 a3 a2 a1 a0 */
for (i= 8; i >= 0; i--)
{
b= (cmd & (1 << i));
b= (b ? 2 : 0);
/* Cmd goes out on the rising edge of the clock */
outb_reg3(dep, 1, 0x80 | 0x8 | b);
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4 | b);
}
for (i= 15; i >= 0; i--)
{
b= (w & (1 << i));
b= (b ? 2 : 0);
/* Cmd goes out on the rising edge of the clock */
outb_reg3(dep, 1, 0x80 | 0x8 | b);
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4 | b);
}
outb_reg3(dep, 1, 0x80 | 0x8); /* End of data */
outb_reg3(dep, 1, 0x80); /* Drop CS */
/* micro_delay(1); */ /* Is this required? */
outb_reg3(dep, 1, 0x80 | 0x8); /* Set CS */
SPIN_UNTIL(inb_reg3(dep, 1) & 1, 10000);
if (!(inb_reg3(dep, 1) & 1))
panic("device remains busy");
}
static void ee_wds(dep)
dpeth_t *dep;
{
int b, i, cmd;
u16_t w;
outb_reg0(dep, DP_CR, CR_PS_P3); /* Bank 3 */
/* Switch to 9346 mode and enable CS */
outb_reg3(dep, 1, 0x80 | 0x8);
cmd= 0x100; /* 1 0 0 0 0 x x x x */
for (i= 8; i >= 0; i--)
{
b= (cmd & (1 << i));
b= (b ? 2 : 0);
/* Cmd goes out on the rising edge of the clock */
outb_reg3(dep, 1, 0x80 | 0x8 | b);
outb_reg3(dep, 1, 0x80 | 0x8 | 0x4 | b);
}
outb_reg3(dep, 1, 0x80 | 0x8); /* End of cmd */
outb_reg3(dep, 1, 0x80); /* Drop CS */
outb_reg3(dep, 1, 0x00); /* back to normal */
outb_reg0(dep, DP_CR, CR_PS_P0); /* back to bank 0 */
}
#endif
static void tell_dev(buf, size, pci_bus, pci_dev, pci_func)
vir_bytes buf;
size_t size;
int pci_bus;
int pci_dev;
int pci_func;
{
int r;
endpoint_t dev_e;
message m;
r= ds_retrieve_label_endpt("amddev", &dev_e);
if (r != OK)
{
#if 0
printf(
"rtl8139`tell_dev: ds_retrieve_label_endpt failed for 'amddev': %d\n",
r);
#endif
return;
}
m.m_type= IOMMU_MAP;
m.m2_i1= pci_bus;
m.m2_i2= pci_dev;
m.m2_i3= pci_func;
m.m2_l1= buf;
m.m2_l2= size;
r= ipc_sendrec(dev_e, &m);
if (r != OK)
{
printf("rtl8139`tell_dev: ipc_sendrec to %d failed: %d\n",
dev_e, r);
return;
}
if (m.m_type != OK)
{
printf("rtl8139`tell_dev: dma map request failed: %d\n",
m.m_type);
return;
}
}
/*
* $PchId: rtl8139.c,v 1.3 2003/09/11 14:15:15 philip Exp $
*/